Ultra Disk DVR 7 Manuel d'utilisateur Page 74
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ALIEN616 User’s Manual V2.0.5
74
4. Set HDD Status to Read-Only.
5. Select OK to save and exit menu.
Note: Once set to read-only, the HDD cannot be written to until it is set back to
read/write (R/W). If the HDD that is currently being written to is set to read-only, the data
will be recorded to the next HDD. If there is only one HDD present, setting it to
read-only will cause the DVR to not record.
11.3.2 Setting HDD to Redundancy
In order to use HDD redundancy on your DVR, you will need to have at least two hard
drives installed. Setting up HDD redundancy will allow your DVR to redundantly record
a copy of the videos onto multiple drives as a safeguard against losing all your files in
case of disk failures.
To setup HDD redundancy:
1. Enter the HDD Management menu by clicking Menu > HDD.
2. Select HDD to setup redundancy on.
3. Select the Property button to enter the Property Settings menu, as shown in
Figure 3.
4. Set HDD Status to Redundancy.
5. Select OK to save and exit menu.
Note: The HDD that is set to redundancy is used to store an extra copy of the recording.
If an HDD is set to redundancy, at least one HDD should be set to the R/W status.
11.4 Checking HDD Status
You may check the status of any of the installed HDDs on your DVR at anytime.
To check the status of an HDD:
1. Enter the HDD Management menu by clicking Menu > HDD.
2. The status of your HDD is listed under the Status column. If the status is
listed as Normal or Hibernate, the HDD is in working order. If it is listed as
Abnormal and has already been initialised, the HDD needs to be replaced. If
the HDD is Uninitialised, you will need to initialise it before it can be used in
your DVR. Please refer to Initialising HDDs for further instructions.
You may also view the SMART information of installed HDDs. SMART, short for
Self-Monitoring, Analysis and Reporting Technology is a monitoring system for hard
disk drives to detect and report on various indicators of reliability in the hopes of
anticipating failures.
- Operations Manual 1
- 1. Introduction 5
- Speaker requires amplifier 7
- 1.4 DVR Operation 8
- ALIEN616 User’s Manual V2.0.5 10
- 1.5 Rear Panel Diagrams 14
- 2. Getting Started 17
- 2.3 Using the Setup Wizard 18
- 2.4 Setting Date & Time 22
- 3. Live Preview 23
- 3.3 Using Digital Zoom 24
- 4.2 Scheduling a Recording 30
- 4.4 Protecting Recorded Files 31
- 5. Playback 36
- 5.1 Playback Methods 37
- 6.3 Managing Backup Devices 44
- 7.2 Setting up Sensor Alarms 47
- 7.4 Detecting Video Loss 50
- 7.6 Setting Exception 53
- 8.3 Configuring DDNS 58
- 8.4 Configuring an NTP Server 59
- 8.6 Configuring Multicast 61
- 9.5 Customising Patrols 66
- 10. Camera Management 69
- 11.3 Setting HDD Status 73
- 11.4 Checking HDD Status 74
- 12. DVR Management 77
- 12.9 Viewing System Logs 88
- 13. Special Features 90
Sharp Job Accounting & Print Release podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Wideo Sharp Job Accounting & Print Release.
Dostarczamy 1 pdf podręczników Sharp Job Accounting & Print Release do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels